Standard Pneumatic Cylinders

AirTAC SE50X200S Standard Pneumatic Cylinder

Model-specific summary: Standard double-acting cylinder with magnetic piston.

Key attributes

Product features

• Complete ordering code retained for procurement and replacement cross-reference.
• Selection-critical connection, voltage and configuration are displayed prominently.
• Designed for industrial pneumatic automation within catalog ratings.

Installation and selection notes

1. Check the complete model code against the product nameplate.
2. Confirm pressure, temperature, medium, mounting and mating interface.
3. Use clean filtered air and remove debris before connection.
4. Non-standard strokes and abbreviated option codes require drawing confirmation before production use.

Quick selection answer

SE50X200S is standard double-acting cylinder with magnetic piston.

Typical applications

Suitable for pneumatic control, positioning, machine automation, maintenance replacement and OEM equipment where the stated configuration matches the system.

Frequently asked questions

What should be checked before ordering?

Verify Series port — verify drawing, Pneumatic — no voltage, 50 mm bore × 200 mm stroke; magnetic piston, dimensions, mounting and accessories.

Can a similar suffix be substituted?

No. A suffix may change thread, voltage, centre function, drain, filter, lead wire, magnetic piston or seal configuration.

PDF datasheet

Download the corresponding AirTAC PDF datasheet

Reviewed against AirTAC catalog ordering rules. Updated 2026-08-22. AirTAC is the manufacturer and trademark owner; this independent listing does not claim official or authorized-distributor status.

AirTAC SE80X400S Standard Pneumatic Cylinder

Model-specific summary: A 80 mm-bore, 400 mm-stroke AirTAC SE Series double-acting cylinder with magnetic piston, standard rear cover and basic mounting.

Key attributes

Product features

• Complete model code retained for replacement and engineering cross-reference.
• Selection-critical connection, power and configuration are displayed before general specifications.
• Designed for industrial automation within the manufacturer limits.

Installation and selection

1. Compare the complete nameplate code with this listing.
2. Confirm pressure, temperature, medium, mounting space and mating interface.
3. Flush air lines and use filtration appropriate to the product.
4. Confirm the complete suffix and manufacturer drawing before ordering.

Quick selection answer

SE80X400S is a 80 mm-bore, 400 mm-stroke AirTAC SE Series double-acting cylinder with magnetic piston, standard rear cover and basic mounting.

Typical applications

Clamping, positioning, feeding, ejecting and general industrial automation.

Frequently asked questions

What should be checked before ordering?

Check the complete suffix, Series air port — verify drawing, Pneumatic — no voltage, 80 mm bore × 400 mm stroke, installation dimensions and compatible accessories.

Can a similar-looking suffix be substituted?

No. Suffixes may change thread, drain, filter grade, pressure range, sensor wiring, mounting or electrical characteristics.

PDF datasheet

Download the corresponding AirTAC PDF datasheet

Reviewed against AirTAC catalog ordering rules. Updated 2026-08-22. AirTAC is the manufacturer and trademark owner; this independent listing does not claim official or authorized-distributor status.

AirTAC SE40X150S Standard Pneumatic Cylinder

Model-specific summary: A 40 mm-bore, 150 mm-stroke AirTAC SE Series double-acting cylinder with magnetic piston, standard rear cover and basic mounting.

Key attributes

Product features

• Complete model code retained for replacement and engineering cross-reference.
• Selection-critical connection, power and configuration are displayed before general specifications.
• Designed for industrial automation within the manufacturer limits.

Installation and selection

1. Compare the complete nameplate code with this listing.
2. Confirm pressure, temperature, medium, mounting space and mating interface.
3. Flush air lines and use filtration appropriate to the product.
4. Confirm the complete suffix and manufacturer drawing before ordering.

Quick selection answer

SE40X150S is a 40 mm-bore, 150 mm-stroke AirTAC SE Series double-acting cylinder with magnetic piston, standard rear cover and basic mounting.

Typical applications

Clamping, positioning, feeding, ejecting and general industrial automation.

Frequently asked questions

What should be checked before ordering?

Check the complete suffix, Series air port — verify drawing, Pneumatic — no voltage, 40 mm bore × 150 mm stroke, installation dimensions and compatible accessories.

Can a similar-looking suffix be substituted?

No. Suffixes may change thread, drain, filter grade, pressure range, sensor wiring, mounting or electrical characteristics.

PDF datasheet

Download the corresponding AirTAC PDF datasheet

Reviewed against AirTAC catalog ordering rules. Updated 2026-08-22. AirTAC is the manufacturer and trademark owner; this independent listing does not claim official or authorized-distributor status.

AirTAC SU40X400 Standard Pneumatic Cylinder

Model-specific summary: A 40 mm-bore, 400 mm-stroke AirTAC SU Series double-acting cylinder, standard rear cover and basic mounting.

Key attributes

Product features

• Complete model code retained for replacement and engineering cross-reference.
• Selection-critical connection, power and configuration are displayed before general specifications.
• Designed for industrial automation within the manufacturer limits.

Installation and selection

1. Compare the complete nameplate code with this listing.
2. Confirm pressure, temperature, medium, mounting space and mating interface.
3. Flush air lines and use filtration appropriate to the product.
4. Confirm the complete suffix and manufacturer drawing before ordering.

Quick selection answer

SU40X400 is a 40 mm-bore, 400 mm-stroke AirTAC SU Series double-acting cylinder, standard rear cover and basic mounting.

Typical applications

Clamping, positioning, feeding, ejecting and general industrial automation.

Frequently asked questions

What should be checked before ordering?

Check the complete suffix, Series air port — verify drawing, Pneumatic — no voltage, 40 mm bore × 400 mm stroke, installation dimensions and compatible accessories.

Can a similar-looking suffix be substituted?

No. Suffixes may change thread, drain, filter grade, pressure range, sensor wiring, mounting or electrical characteristics.

PDF datasheet

Download the corresponding AirTAC PDF datasheet

Reviewed against AirTAC catalog ordering rules. Updated 2026-08-22. AirTAC is the manufacturer and trademark owner; this independent listing does not claim official or authorized-distributor status.

AirTAC SU63X1000 Standard Pneumatic Cylinder

Model-specific summary: A 63 mm-bore, 1000 mm-stroke AirTAC SU Series double-acting cylinder, standard rear cover and basic mounting.

Key attributes

Product features

• Complete model code retained for replacement and engineering cross-reference.
• Selection-critical connection, power and configuration are displayed before general specifications.
• Designed for industrial automation within the manufacturer limits.

Installation and selection

1. Compare the complete nameplate code with this listing.
2. Confirm pressure, temperature, medium, mounting space and mating interface.
3. Flush air lines and use filtration appropriate to the product.
4. Confirm the complete suffix and manufacturer drawing before ordering.

Quick selection answer

SU63X1000 is a 63 mm-bore, 1000 mm-stroke AirTAC SU Series double-acting cylinder, standard rear cover and basic mounting.

Typical applications

Clamping, positioning, feeding, ejecting and general industrial automation.

Frequently asked questions

What should be checked before ordering?

Check the complete suffix, Series air port — verify drawing, Pneumatic — no voltage, 63 mm bore × 1000 mm stroke, installation dimensions and compatible accessories.

Can a similar-looking suffix be substituted?

No. Suffixes may change thread, drain, filter grade, pressure range, sensor wiring, mounting or electrical characteristics.

PDF datasheet

Download the corresponding AirTAC PDF datasheet

Reviewed against AirTAC catalog ordering rules. Updated 2026-08-22. AirTAC is the manufacturer and trademark owner; this independent listing does not claim official or authorized-distributor status.

AirTAC SC32X200S Standard Tie-Rod Pneumatic Cylinder

Model-specific summary: A 32 mm-bore, 200 mm-stroke SC Series double-acting pneumatic cylinder with magnetic piston.

Key attributes

Product features

• Complete ordering code retained for accurate replacement and cross-reference work.
• Designed for industrial pneumatic automation within the manufacturer ratings.
• Selection-critical connection, voltage and function are shown above before general specifications.

Installation and commissioning

1. Compare the complete model code and nameplate before installation.
2. Confirm flow direction, port standard, supply conditions and mounting clearance.
3. Use properly filtered air and remove pipe debris before connection.
4. Ordering code reviewed against the series rules; confirm the nameplate and dimensional drawing before purchase.

Quick selection answer

SC32X200S is a 32 mm-bore, 200 mm-stroke SC Series double-acting pneumatic cylinder with magnetic piston.

Typical applications

Clamping, positioning, feeding, ejecting and general industrial automation.

Frequently asked questions

What should be checked before ordering?

Verify the entire suffix, PT 1/8, Not applicable, function, mounting and operating limits. A similar-looking model may have a different centre function, voltage or thread.

Are PT, G and NPT interchangeable?

No. Their thread profiles and sealing methods differ. Select the exact regional thread code.

PDF datasheet

Download the corresponding AirTAC PDF datasheet

Reviewed against AirTAC catalog ordering rules. Updated 2026-08-21. AirTAC is the manufacturer and trademark owner; this independent product listing does not claim official or authorized-distributor status.

AirTAC SC40X150S Standard Tie-Rod Pneumatic Cylinder

Model-specific summary: A 40 mm-bore, 150 mm-stroke SC Series double-acting pneumatic cylinder with magnetic piston.

Key attributes

Product features

• Complete ordering code retained for accurate replacement and cross-reference work.
• Designed for industrial pneumatic automation within the manufacturer ratings.
• Selection-critical connection, voltage and function are shown above before general specifications.

Installation and commissioning

1. Compare the complete model code and nameplate before installation.
2. Confirm flow direction, port standard, supply conditions and mounting clearance.
3. Use properly filtered air and remove pipe debris before connection.
4. Ordering code reviewed against the series rules; confirm the nameplate and dimensional drawing before purchase.

Quick selection answer

SC40X150S is a 40 mm-bore, 150 mm-stroke SC Series double-acting pneumatic cylinder with magnetic piston.

Typical applications

Clamping, positioning, feeding, ejecting and general industrial automation.

Frequently asked questions

What should be checked before ordering?

Verify the entire suffix, PT 1/4, Not applicable, function, mounting and operating limits. A similar-looking model may have a different centre function, voltage or thread.

Are PT, G and NPT interchangeable?

No. Their thread profiles and sealing methods differ. Select the exact regional thread code.

PDF datasheet

Download the corresponding AirTAC PDF datasheet

Reviewed against AirTAC catalog ordering rules. Updated 2026-08-21. AirTAC is the manufacturer and trademark owner; this independent product listing does not claim official or authorized-distributor status.

AirTAC SC40X75 Standard Tie-Rod Pneumatic Cylinder

Model-specific summary: A 40 mm-bore, 75 mm-stroke SC Series double-acting pneumatic cylinder.

Key attributes

Product features

• Complete ordering code retained for accurate replacement and cross-reference work.
• Designed for industrial pneumatic automation within the manufacturer ratings.
• Selection-critical connection, voltage and function are shown above before general specifications.

Installation and commissioning

1. Compare the complete model code and nameplate before installation.
2. Confirm flow direction, port standard, supply conditions and mounting clearance.
3. Use properly filtered air and remove pipe debris before connection.
4. Ordering code reviewed against the series rules; confirm the nameplate and dimensional drawing before purchase.

Quick selection answer

SC40X75 is a 40 mm-bore, 75 mm-stroke SC Series double-acting pneumatic cylinder.

Typical applications

Clamping, positioning, feeding, ejecting and general industrial automation.

Frequently asked questions

What should be checked before ordering?

Verify the entire suffix, PT 1/4, Not applicable, function, mounting and operating limits. A similar-looking model may have a different centre function, voltage or thread.

Are PT, G and NPT interchangeable?

No. Their thread profiles and sealing methods differ. Select the exact regional thread code.

PDF datasheet

Download the corresponding AirTAC PDF datasheet

Reviewed against AirTAC catalog ordering rules. Updated 2026-08-21. AirTAC is the manufacturer and trademark owner; this independent product listing does not claim official or authorized-distributor status.

Airtac SC80X75 SC Series Tie-Rod Pneumatic Cylinder

Model-specific summary: The Airtac SC80X75 is a double-acting SC Series standard tie-rod air cylinder with a 80 mm bore and 75 mm stroke, without a magnetic piston code. It is intended for repeatable linear extension and retraction in general industrial machinery.

Key specifications

Construction and operating advantages

• Front and rear covers are joined to the aluminum barrel by tie rods for a rigid, service-proven structure.
• The profiled two-way piston seal is compact and incorporates grease-retaining geometry.
• Air cushioning at both ends can be adjusted for smoother end-of-stroke deceleration.
• The SC body is shorter than an ISO 15552 cylinder of the same bore, while retaining conventional tie-rod construction.
• Multiple mounting accessories support foot, flange, clevis and trunnion-style machine layouts.
• High-temperature seal configurations are available at series level for operation up to 150 °C; this is not implied by the standard model code shown here.

Installation and commissioning

1. Size the cylinder with sufficient output margin for actual load variation; theoretical force alone is not the usable machine force.
2. Flush the air line before connection and supply air filtered to 40 μm or finer.
3. Protect the cylinder from heavy dust, water droplets, oil mist, weld spatter and freezing condensate.
4. During initial no-load testing, start with conservative cushion adjustment and open gradually to avoid excessive impact.
5. Avoid unsupported side load on the piston rod and verify alignment over the full 75 mm travel.

Quick selection answer

SC80X75 is a 80 mm bore, 75 mm stroke, double-acting standard pneumatic cylinder.

Typical applications

Suitable for packaging machinery, conveyors, clamping fixtures, material handling equipment and general industrial automation requiring linear motion.

Selection and compatibility notes

• Catalog-valid standard configuration. The catalog pressure and speed limits do not replace application-specific force and kinetic-energy calculations.
• Confirm the complete model code, installation space and operating conditions before purchase.
• Product selection must be verified against the machine load, speed, duty cycle and safety requirements.

Frequently asked questions

What is SC80X75 used for?

Suitable for packaging machinery, conveyors, clamping fixtures, material handling equipment and general industrial automation requiring linear motion.

How does this model differ from related products?

Compared with a compact cylinder, the SC tie-rod design is better suited to longer strokes and conventional industrial mounting. Bore and stroke must still be sized from required force and travel.

What should be checked before ordering?

Check the model code, dimensions, operating conditions, mounting method and required accessories. Refer to the manufacturer catalog drawing for final engineering approval.

Technical reference

View the official AirTAC SC Series product reference

Technical content reviewed against the AirTAC 2026 product catalog. Last updated: 2026-08-20. AirTAC is the product manufacturer and trademark owner; this page is an independent product listing and does not claim to be the official AirTAC website or an authorized distributor.

Airtac SC100X125 SC Series Tie-Rod Pneumatic Cylinder

Model-specific summary: The Airtac SC100X125 is a double-acting SC Series standard tie-rod air cylinder with a 100 mm bore and 125 mm stroke, without a magnetic piston code. It is intended for repeatable linear extension and retraction in general industrial machinery.

Key specifications

Construction and operating advantages

• Front and rear covers are joined to the aluminum barrel by tie rods for a rigid, service-proven structure.
• The profiled two-way piston seal is compact and incorporates grease-retaining geometry.
• Air cushioning at both ends can be adjusted for smoother end-of-stroke deceleration.
• The SC body is shorter than an ISO 15552 cylinder of the same bore, while retaining conventional tie-rod construction.
• Multiple mounting accessories support foot, flange, clevis and trunnion-style machine layouts.
• High-temperature seal configurations are available at series level for operation up to 150 °C; this is not implied by the standard model code shown here.

Installation and commissioning

1. Size the cylinder with sufficient output margin for actual load variation; theoretical force alone is not the usable machine force.
2. Flush the air line before connection and supply air filtered to 40 μm or finer.
3. Protect the cylinder from heavy dust, water droplets, oil mist, weld spatter and freezing condensate.
4. During initial no-load testing, start with conservative cushion adjustment and open gradually to avoid excessive impact.
5. Avoid unsupported side load on the piston rod and verify alignment over the full 125 mm travel.

Quick selection answer

SC100X125 is a 100 mm bore, 125 mm stroke, double-acting standard pneumatic cylinder.

Typical applications

Suitable for packaging machinery, conveyors, clamping fixtures, material handling equipment and general industrial automation requiring linear motion.

Selection and compatibility notes

• Catalog-valid standard configuration. The catalog pressure and speed limits do not replace application-specific force and kinetic-energy calculations.
• Confirm the complete model code, installation space and operating conditions before purchase.
• Product selection must be verified against the machine load, speed, duty cycle and safety requirements.

Frequently asked questions

What is SC100X125 used for?

Suitable for packaging machinery, conveyors, clamping fixtures, material handling equipment and general industrial automation requiring linear motion.

How does this model differ from related products?

Compared with a compact cylinder, the SC tie-rod design is better suited to longer strokes and conventional industrial mounting. Bore and stroke must still be sized from required force and travel.

What should be checked before ordering?

Check the model code, dimensions, operating conditions, mounting method and required accessories. Refer to the manufacturer catalog drawing for final engineering approval.

Technical reference

View the official AirTAC SC Series product reference

Technical content reviewed against the AirTAC 2026 product catalog. Last updated: 2026-08-20. AirTAC is the product manufacturer and trademark owner; this page is an independent product listing and does not claim to be the official AirTAC website or an authorized distributor.

Airtac SC40X90S SC Series Tie-Rod Pneumatic Cylinder

Model-specific summary: The Airtac SC40X90S is a double-acting SC Series standard tie-rod air cylinder with a 40 mm bore and 90 mm stroke, plus a magnetic piston for compatible position sensors. It is intended for repeatable linear extension and retraction in general industrial machinery.

Key specifications

Construction and operating advantages

• Front and rear covers are joined to the aluminum barrel by tie rods for a rigid, service-proven structure.
• The profiled two-way piston seal is compact and incorporates grease-retaining geometry.
• Air cushioning at both ends can be adjusted for smoother end-of-stroke deceleration.
• The SC body is shorter than an ISO 15552 cylinder of the same bore, while retaining conventional tie-rod construction.
• Multiple mounting accessories support foot, flange, clevis and trunnion-style machine layouts.
• The magnetic piston allows compatible sensors to be mounted on the cylinder tie rods for end-position feedback.
• High-temperature seal configurations are available at series level for operation up to 150 °C; this is not implied by the standard model code shown here.

Installation and commissioning

1. Size the cylinder with sufficient output margin for actual load variation; theoretical force alone is not the usable machine force.
2. Flush the air line before connection and supply air filtered to 40 μm or finer.
3. Protect the cylinder from heavy dust, water droplets, oil mist, weld spatter and freezing condensate.
4. During initial no-load testing, start with conservative cushion adjustment and open gradually to avoid excessive impact.
5. Avoid unsupported side load on the piston rod and verify alignment over the full 90 mm travel.

Quick selection answer

SC40X90S is a 40 mm bore, 90 mm stroke, double-acting standard pneumatic cylinder with a magnetic piston.

Typical applications

Suitable for packaging machinery, conveyors, clamping fixtures, material handling equipment and general industrial automation requiring linear motion.

Selection and compatibility notes

• Non-standard catalog stroke; 90 mm is within the SC40 maximum stroke range. Confirm made-to-order availability. The catalog pressure and speed limits do not replace application-specific force and kinetic-energy calculations.
• Confirm the complete model code, installation space and operating conditions before purchase.
• Product selection must be verified against the machine load, speed, duty cycle and safety requirements.

Frequently asked questions

What is SC40X90S used for?

Suitable for packaging machinery, conveyors, clamping fixtures, material handling equipment and general industrial automation requiring linear motion.

How does this model differ from related products?

Compared with a compact cylinder, the SC tie-rod design is better suited to longer strokes and conventional industrial mounting. Bore and stroke must still be sized from required force and travel.

What should be checked before ordering?

Check the model code, dimensions, operating conditions, mounting method and required accessories. Refer to the manufacturer catalog drawing for final engineering approval.

Technical reference

View the official AirTAC SC Series product reference

Technical content reviewed against the AirTAC 2026 product catalog. Last updated: 2026-08-20. AirTAC is the product manufacturer and trademark owner; this page is an independent product listing and does not claim to be the official AirTAC website or an authorized distributor.

Airtac SC63X125S SC Series Tie-Rod Pneumatic Cylinder

Model-specific summary: The Airtac SC63X125S is a double-acting SC Series standard tie-rod air cylinder with a 63 mm bore and 125 mm stroke, plus a magnetic piston for compatible position sensors. It is intended for repeatable linear extension and retraction in general industrial machinery.

Key specifications

Construction and operating advantages

• Front and rear covers are joined to the aluminum barrel by tie rods for a rigid, service-proven structure.
• The profiled two-way piston seal is compact and incorporates grease-retaining geometry.
• Air cushioning at both ends can be adjusted for smoother end-of-stroke deceleration.
• The SC body is shorter than an ISO 15552 cylinder of the same bore, while retaining conventional tie-rod construction.
• Multiple mounting accessories support foot, flange, clevis and trunnion-style machine layouts.
• The magnetic piston allows compatible sensors to be mounted on the cylinder tie rods for end-position feedback.
• High-temperature seal configurations are available at series level for operation up to 150 °C; this is not implied by the standard model code shown here.

Installation and commissioning

1. Size the cylinder with sufficient output margin for actual load variation; theoretical force alone is not the usable machine force.
2. Flush the air line before connection and supply air filtered to 40 μm or finer.
3. Protect the cylinder from heavy dust, water droplets, oil mist, weld spatter and freezing condensate.
4. During initial no-load testing, start with conservative cushion adjustment and open gradually to avoid excessive impact.
5. Avoid unsupported side load on the piston rod and verify alignment over the full 125 mm travel.

Quick selection answer

SC63X125S is a 63 mm bore, 125 mm stroke, double-acting standard pneumatic cylinder with a magnetic piston.

Typical applications

Suitable for packaging machinery, conveyors, clamping fixtures, material handling equipment and general industrial automation requiring linear motion.

Selection and compatibility notes

• Catalog-valid standard configuration. The catalog pressure and speed limits do not replace application-specific force and kinetic-energy calculations.
• Confirm the complete model code, installation space and operating conditions before purchase.
• Product selection must be verified against the machine load, speed, duty cycle and safety requirements.

Frequently asked questions

What is SC63X125S used for?

Suitable for packaging machinery, conveyors, clamping fixtures, material handling equipment and general industrial automation requiring linear motion.

How does this model differ from related products?

Compared with a compact cylinder, the SC tie-rod design is better suited to longer strokes and conventional industrial mounting. Bore and stroke must still be sized from required force and travel.

What should be checked before ordering?

Check the model code, dimensions, operating conditions, mounting method and required accessories. Refer to the manufacturer catalog drawing for final engineering approval.

Technical reference

View the official AirTAC SC Series product reference

Technical content reviewed against the AirTAC 2026 product catalog. Last updated: 2026-08-20. AirTAC is the product manufacturer and trademark owner; this page is an independent product listing and does not claim to be the official AirTAC website or an authorized distributor.

Airtac SC63X500S SC Series Tie-Rod Pneumatic Cylinder

Model-specific summary: The Airtac SC63X500S is a double-acting SC Series standard tie-rod air cylinder with a 63 mm bore and 500 mm stroke, plus a magnetic piston for compatible position sensors. It is intended for repeatable linear extension and retraction in general industrial machinery.

Key specifications

Construction and operating advantages

• Front and rear covers are joined to the aluminum barrel by tie rods for a rigid, service-proven structure.
• The profiled two-way piston seal is compact and incorporates grease-retaining geometry.
• Air cushioning at both ends can be adjusted for smoother end-of-stroke deceleration.
• The SC body is shorter than an ISO 15552 cylinder of the same bore, while retaining conventional tie-rod construction.
• Multiple mounting accessories support foot, flange, clevis and trunnion-style machine layouts.
• The magnetic piston allows compatible sensors to be mounted on the cylinder tie rods for end-position feedback.
• High-temperature seal configurations are available at series level for operation up to 150 °C; this is not implied by the standard model code shown here.

Installation and commissioning

1. Size the cylinder with sufficient output margin for actual load variation; theoretical force alone is not the usable machine force.
2. Flush the air line before connection and supply air filtered to 40 μm or finer.
3. Protect the cylinder from heavy dust, water droplets, oil mist, weld spatter and freezing condensate.
4. During initial no-load testing, start with conservative cushion adjustment and open gradually to avoid excessive impact.
5. Avoid unsupported side load on the piston rod and verify alignment over the full 500 mm travel.

Quick selection answer

SC63X500S is a 63 mm bore, 500 mm stroke, double-acting standard pneumatic cylinder with a magnetic piston.

Typical applications

Suitable for packaging machinery, conveyors, clamping fixtures, material handling equipment and general industrial automation requiring linear motion.

Selection and compatibility notes

• Catalog-valid standard configuration. The catalog pressure and speed limits do not replace application-specific force and kinetic-energy calculations.
• Confirm the complete model code, installation space and operating conditions before purchase.
• Product selection must be verified against the machine load, speed, duty cycle and safety requirements.

Frequently asked questions

What is SC63X500S used for?

Suitable for packaging machinery, conveyors, clamping fixtures, material handling equipment and general industrial automation requiring linear motion.

How does this model differ from related products?

Compared with a compact cylinder, the SC tie-rod design is better suited to longer strokes and conventional industrial mounting. Bore and stroke must still be sized from required force and travel.

What should be checked before ordering?

Check the model code, dimensions, operating conditions, mounting method and required accessories. Refer to the manufacturer catalog drawing for final engineering approval.

Technical reference

View the official AirTAC SC Series product reference

Technical content reviewed against the AirTAC 2026 product catalog. Last updated: 2026-08-20. AirTAC is the product manufacturer and trademark owner; this page is an independent product listing and does not claim to be the official AirTAC website or an authorized distributor.

Airtac SC80X650S SC Series Tie-Rod Pneumatic Cylinder

Model-specific summary: The Airtac SC80X650S is a double-acting SC Series standard tie-rod air cylinder with a 80 mm bore and 650 mm stroke, plus a magnetic piston for compatible position sensors. It is intended for repeatable linear extension and retraction in general industrial machinery.

Key specifications

Construction and operating advantages

• Front and rear covers are joined to the aluminum barrel by tie rods for a rigid, service-proven structure.
• The profiled two-way piston seal is compact and incorporates grease-retaining geometry.
• Air cushioning at both ends can be adjusted for smoother end-of-stroke deceleration.
• The SC body is shorter than an ISO 15552 cylinder of the same bore, while retaining conventional tie-rod construction.
• Multiple mounting accessories support foot, flange, clevis and trunnion-style machine layouts.
• The magnetic piston allows compatible sensors to be mounted on the cylinder tie rods for end-position feedback.
• High-temperature seal configurations are available at series level for operation up to 150 °C; this is not implied by the standard model code shown here.

Installation and commissioning

1. Size the cylinder with sufficient output margin for actual load variation; theoretical force alone is not the usable machine force.
2. Flush the air line before connection and supply air filtered to 40 μm or finer.
3. Protect the cylinder from heavy dust, water droplets, oil mist, weld spatter and freezing condensate.
4. During initial no-load testing, start with conservative cushion adjustment and open gradually to avoid excessive impact.
5. Avoid unsupported side load on the piston rod and verify alignment over the full 650 mm travel.

Quick selection answer

SC80X650S is a 80 mm bore, 650 mm stroke, double-acting standard pneumatic cylinder with a magnetic piston.

Typical applications

Suitable for packaging machinery, conveyors, clamping fixtures, material handling equipment and general industrial automation requiring linear motion.

Selection and compatibility notes

• Non-standard catalog stroke; 650 mm is within the SC80 maximum stroke range. Confirm made-to-order availability. The catalog pressure and speed limits do not replace application-specific force and kinetic-energy calculations.
• Confirm the complete model code, installation space and operating conditions before purchase.
• Product selection must be verified against the machine load, speed, duty cycle and safety requirements.

Frequently asked questions

What is SC80X650S used for?

Suitable for packaging machinery, conveyors, clamping fixtures, material handling equipment and general industrial automation requiring linear motion.

How does this model differ from related products?

Compared with a compact cylinder, the SC tie-rod design is better suited to longer strokes and conventional industrial mounting. Bore and stroke must still be sized from required force and travel.

What should be checked before ordering?

Check the model code, dimensions, operating conditions, mounting method and required accessories. Refer to the manufacturer catalog drawing for final engineering approval.

Technical reference

View the official AirTAC SC Series product reference

Technical content reviewed against the AirTAC 2026 product catalog. Last updated: 2026-08-20. AirTAC is the product manufacturer and trademark owner; this page is an independent product listing and does not claim to be the official AirTAC website or an authorized distributor.